Bronze Alloys according to ASTM B505, ASTM B271 y ASTM B22 WISCO manufactures alloys according to the ASTM B505 continuous casting and the ASTM B271 centrifugal casting standards. We are carry references in stock that comply with the standard or have similar characteristics.
Alloys according to EN 1982 Standard - WiscoAlloys according to EN 1982 Standard We manufacture an extensive range of continuous and centrifugal cast bronzes according to European standard EN 1982. We have 1.500 tonnes of permanent stock that complies with this standard in our automated warehouse.
The bronze is a metal alloy, mainly composed of copper which is enriched with other elements such as aluminum, nickel, beryllium or tin, to be combined in the most varied alloys. These alloys give the bronze various chemical-physical and mechanical characteristics. The bronze is very versatile and can be used for bushings, skids, sliding gantry, gears, toothed wheels, bearings, furniture
Bronze & BrassCuZn34Al2Mn3Fe1 CC764S CuZn34Al2 High mechanical properties, middle cutting property. Statically loaded parts, valve and control parts. CuZn25AL5Mn4Fe3 C86200 CC762S HTB3 CuZn25AL5 Marine technology, gears, gun mounts, bushings and
Bs 1400-Copper & Copper Alloys - ScribdCopper and Copper Alloys. Conversion of Old BS into EN Material Designations Table 5:Copper and Copper Alloy Ingots and Castings - Comparison of BS 1400 and EN 1982 Showing near equivalents where standardised in EN 1982 and original compositional symbols for guidance where no near equivalent is included. See Table 7 for full details of compositions and properties.
7 Introduction to Standards Table 1:EN Standards for Copper and Copper Alloys EN Number Title Nearest Old BS Equivalent Unwrought Products 1976 Cast unwrought copper products Copper drawing stock (wire rod) Copper cathodes Master alloys Ingots and castings 1400 Rolled Flat Products 1172 Sheet and strip for building purposes Plate, sheet, strip
Fls Material Codes [30j8pg6r45lw]Quality .55% Carbon Steel Copper Bellyllium Alloy Rod, Bar Casting Composite Product Mtl:7043 (Casing/Cover) and CD4M Impeller Commercial Carbon Steel Drill Rod Austenitic CRNIMO Wrought SS Per EN10088-1, WN 1.4401 (=316) Aust.CRNIMO, Low C, Wrought SS Per EN10088-1, WN 1.4404 (=316L) DIN 1.4408 (Eurpean Version of CF8M) High Quality 0.75%
I 018 e Machining Industrial ProcessesTranslate this pageThe mechanical properties of the wrought alloys listed in the following tables refer mainly to rods and bars (as defined in EN 12164, EN 12163, EN 13601 and EN 12166, strip (as in EN 1652 and EN 1654) and tubes (as in EN 12449). The values for the cast alloys are from EN 1982. The order in which the alloy groups are presented follows CEN/TS 13388.
We supply ex stock:Special Brass, CuZn37Mn3Al2PbSi, CW713R, 2.0550, CuZn35Ni3Mn2AlPb, CW710R, 2.0540, CuZn40Mn2Fe1, CuZn31Si1, CuZn25Al5
laiton - euralliageFor other foreign correspondences, see:Chart correspondences among the main foreign standards and:Chemical components according to foreign standards:CC764S - Finkelstein Metals Finkelstein Metals* In Determining Cu min, Cu may be calculated as Cu + Ni. Note:Cu + Sum of Named Elements, 99.5% min. ** For permanent mould castings, the minimum manganese content shall